Selasa, 15 Januari 2013

CCNA 1 Exam Networking Answers (Chapter 8)

CCNA 1 Exam Networking Answers (Chapter 8)


1. Which OSI layer is responsible for binary transmission, cable specification, and physical aspects of network communication?
• Presentation
• Transport
• Data Link
• Physical


2. An installed fiber run can be checked for faults, integrity, and the performance of the media by using what device?
• light injector
• OTDR
• TDR
• multimeter
3. Which characteristics describe fiber optic cable? (Choose two.)
• It is not affected by EMI or RFI.
• Each pair of cables is wrapped in metallic foil.
• It combines the technique of cancellation, shielding and twisting to protect data.
• It has a maximum speed of 100 Mbps.
• It is the most expensive type of LAN cabling.

4. When is a straight-through cable used in a network?
• when connecting a router through the console port
• when connecting one switch to another switch
• when connecting a host to a switch
• when connecting a router to another router
5. Refer to the exhibit. Which type of Category 5 cable is used to make an Ethernet connection between Host A and Host B?
• coax cable
• rollover cable
• crossover cable
• straight-through cable
6. Which method of signal transmission uses radio waves to carry signals?
• electrical
• optical
• wireless
• acoustic
7. In most business LANs, which connector is used with twisted-pair networking cable?
• BNC
• RJ-11
• RJ-45
• Type F
8. Which of the following is a characteristic of single-mode fiber-optic cable?
• generally uses LEDs as the light source
• relatively larger core with multiple light paths
• less expensive than multimode
• generally uses lasers as the light source

9. Which type of cable run is most often associated with fiber-optic cable?
• backbone cable
• horizontal cable
• patch cable
• work area cable
10. What are three measures of data transfer? (Choose three.)
• goodput
• frequency
• amplitude
• throughput
• crosstalk
• bandwidth

11. With the use of unshielded twisted-pair copper wire in a network, what causes crosstalk within the cable pairs?
• the magnetic field around the adjacent pairs of wire
• the use of braided wire to shield the adjacent wire pairs
• the reflection of the electrical wave back from the far end of the cable
• the collision caused by two nodes trying to use the media simultaneously
12. What is a primary role of the Physical layer in transmitting data on the network?
• create the signals that represent the bits in each frame on to the media
• provide physical addressing to the devices
• determine the path packets take through the network
• control data access to the media
13. In LAN installations where potential electrical hazards or electromagnetic interference may be present, what type of media is recommended for backbone cabling?
• coax
• fiber
• Cat5e UTP
• Cat6 UTP
• STP
14. What is a possible effect of improperly applying a connector to a network cable?
• Data will be forwarded to the wrong node.
• Data transmitted through that cable may experience signal loss.
• An improper signaling method will be implemented for data transmitted on that cable.
• The encoding method for data sent on that cable will change to compensate for the improper connection.
15. Which fiber connector supports full duplex Ethernet?
• Options three is right answer (
kolmas)

16. What is considered a benefit of wireless as a media choice?
• more host mobility
• lower security risks
• reduced susceptibility to interference
• less impact of the surroundings on the effective coverage area
17. What characteristic of UTP cable helps reduce the effects of interference?
• the metal braiding in the shielding
• the reflective cladding around core
• the twisting of the wires in the cable
• the insulating material in the outer jacket
Refer to the exhibit. An ISP donates some decommissioned Cisco 2600 series routers to a local high school.  The high school plans to use these routers in their networking classrooms for students to practice. Which type of cable is used to make an Ethernet connection between routers RTA and RTB?
coax cable
rollover cable
——->crossover cable
straight-through cable
Which data communications standard provides broadband access in a wireless network?
GSM
Wi-Fi
——>WiMAX
Bluetooth
When is a rollover cable used in a network?
for connecting a host to a Fast Ethernet port on a switch
for connecting a router to another router
for connecting two routers through their AUX ports
jawab: for connecting to a switch through its console port
Which OSI layer is responsible for managing optical signals used for data communication?
physical
A customer installs a wireless access point at home in the closet next to the kitchen. The customer mentions that the wireless communication performance seems degraded when the cordless phone or the microwave oven is in use. What is the possible reason for this degradation?
The wireless signal is in the same radio frequency range as the household devices are in.
Which fiber connector supports full duplex Ethernet?
Option 3
Compared with UTP cable, what extra characteristic of STP cable helps reduce the effects of interference?
the metal braiding in the shielding

Tidak ada komentar:

Posting Komentar